Whittlesea Building
Inspections

Bored pier inspection in Whittlesea

Verified while the hole is still open, the depth, diameter and cage position must be correct.

  • After drilling and cage placement, before concrete
  • About 1 hour on site
  • Report within 24 hours
Get a quoteLeave your details here and we will send you a price

No obligation. We use your details for your quote and may contact you about it even if you don't finish.

Fully licensed & accredited

Stage1 of 7
When to bookAfter drilling and cage placement, before concrete
Time on siteAbout 1 hour on site
Inspected againstAS 2870, AS 3600, the geotechnical report and the engineer's footing design

What is included in a Whittlesea bored piers inspection

  • Pier positions and spacing against the footing plan
  • Pier diameter checked at the top of each hole
  • Depth against the engineer's design and the soil report
  • Founding material at the base where visible
  • Reinforcement cage size, laps and starter bars
  • Cover to the cage and centralisers
  • Hole cleanliness, spoil and loose material
  • Standing water or seepage before the pour
  • Steel projection into the slab or beam
  • Termite and service penetrations near piers
  • Set-out against the site plan and boundaries
  • Records and photographs for the engineer where required
Why it matters here

Bored piers inspections on Whittlesea builds

Piers are installed on Whittlesea lots where the ground requires support beyond the surface, particularly on land with a history of timber logging or earthworks. The town sits just outside the Urban Growth Boundaries and many sites have a rural character, which often means the founding material is not rock and requires deep holes. Depth must be verified before the concrete is poured, so the inspection must occur between boring and filling.

What we find at this stage in Whittlesea

  • Found that the pier depth does not match the engineering details.
  • Cover sits unevenly on the cage centre
  • Water or soil pooling at the building base
  • The metal frame was not secured at the base of the excavation.
  • Concrete reinforcement lacks adequate support before pouring
Fill up slab under shower tray, recorded during a slab pre-pour inspection in Beveridge
The inspector found the area under the shower tray was filled up, which may affect drainage, Beveridge
Sample findings

Sample defects found during our bored piers inspections in Whittlesea

Annotated findings from Bored piers inspections.

Trimming required, recorded during a slab pre-pour inspection in Beveridge
The shower recess is too large, which stops the plaster sitting flush against the wall, Beveridge
Timber wall overhang exceeds 10mm, recorded during a slab pre-pour inspection in Beveridge
Timber frame bottom plates overhang the concrete slab by more than 10mm, which may affect structural support, Beveridge
Extension required, recorded during a slab pre-pour inspection in Beveridge
The concrete recess penetrates the wall frame, which stops the plaster sitting properly, Beveridge
Reinforcement laps not enough, recorded during a slab pre-pour inspection in Beveridge
Reinforcement laps were not long enough in the structure, Beveridge

The other stages of a Whittlesea build

  1. Slab pre-pour inspection in Whittlesea2Slab pre-pourThe day before pouring, before waterproofing
  2. Frame inspection in Whittlesea3FrameAfter wall frame erection and bracing, before lining
  3. Lock-up (pre-plaster) inspection in Whittlesea4Lock-up (pre-plaster)After roof cladding and external doors, before plasterboard
  4. Fixing inspection in Whittlesea5FixingAfter joinery and doors installed, before painting
  5. Waterproofing inspection in Whittlesea6WaterproofingAfter membrane application and prior to tiling
  6. Pre-handover (PCI) inspection in Whittlesea7Pre-handover (PCI)Two to three weeks prior to handover

All construction stage inspections in Whittlesea →

Guides

Construction stage guides for Whittlesea

All guides →

Book a bored piers inspection in Whittlesea

Instant online pricing for Whittlesea, or contact the booking team.

FAQ

Bored piers inspections in Whittlesea: common questions

How long for the report?

We usually finish existing home inspections within an hour, though complex sites or lots with high numbers of piers take longer.

Is the pier depth correct?

We note the required depth in the plan and verify the depth of the excavation. Identifying the problem while it is still visible helps the builder and their engineer fix the issue.

Are the footings certified?

No. We check against engineering plans. Engineers design footings and specify where they are required in the report.

Is standing bore water a problem?

Concrete poured into water will not achieve its designed strength at the base. We check the drainage so concrete can be poured without issues.

How soon can you do a stage inspection after the piers are poured?

As little as a day. Bored and filled piers usually take forty eight hours to complete, so it is best to contact us as soon as the date is set.

What materials should I send?

The engineered drawings for your site detail the pier depth, diameter and placement. We can confirm the current state of the property, yet the inspection will not reveal if the build complies with the approved plans and standards.

Get a Free Quote